Accessories for Mobil Tech Stands

These products can Now be ordered in our New Online Store!

To compliment all of their stands, Mobil Tech International offers a complete line of adaptors and accessories. Every accessory has been carefully designed and engineered to install with ease and support the intended application. There are different accessories for each series of stands, so we have listed in detail which accessory goes with which stand. Because Mobil Tech accessories are made in the UK, you will see metric sizes listed for shaft size. We have converted them to imperial for your convenience.

29 mm = 1.14 inches
35 mm = 1.38 inches
50 mm = 1.97 inches

The following is our complete selection
of accessories.

Truss Adaptors
Made From Zinc Plated Steel

TAdaptor 150/200: Adjustable 6" to 10" Truss Adaptor

This adaptor is sold only as a replacement part for the DJ Truss System and has a 29 mm shaft. This adaptor will not fit any of the other stands.

TAdaptor 250/300: Adjustable 8" to 12" Truss Adaptor

Adjustable 8" to 12" Truss Adaptor that has a 35 mm shaft and is used on the StandTek 3000, SpTek 4000 and the AlpTek 45 stands. It can also be used on the AlpTek 5500 and 6500, which has 50 mm shaft by using an Rlp5 Adaptor with it. Designed to accommodate 8" to 12" Tri or Box Truss.

TAdaptor TAlp5: Adjustable 10" to 20" Truss Adaptor

Adjustable 10" to 20" Truss Adaptor that has a 50 mm shaft and is used on the AlpTek 5500 and 6500 stands only. This adaptor will not work on the StandTek 3000, SpTek 4000 or the AlpTek 45 stands. Designed to accommodate Tri or Box truss from 10" to 20" wide.

TBars
Made from Steel and painted Black Epoxy

TB3 Tbar

The TB3 has a 35mm shaft and is used on the StandTek 3000, SpTek 4000 and the AlpTek 45 stands. It can also be used on the AlpTek 5500 and 6500 stands with the aid of a Rlp5 adaptor. Made from 2" black pipe, the TBar3 is 5 feet long and is painted with black epoxy paint for durability. The ends are capped for a professional look. The 35 mm center shaft has 2 additional gusset braces for additional strength, allowing the TBar3 to accommodate up to 6 lights. Lights can be attached with ease using the Hook Clamp 50P.

TB6 TBar

The TB6 has a 35 mm shaft and is used on the StandTek 3000, SpTek 4000 and the AlpTek 45 stands. It can also be used on the AlpTek 5500 and 6500 stands with the aid of a Rlp5 adaptor. Made from 1" steel square tube, the TBar6 is 5 feet long and is painted with black epoxy paint for durability. Lights are mounted with bolts and wing nuts that are included and can accommodate up to 6 lights on the top and 6 lights on the bottom. The top and bottom light will share the same bolt.

TubeTop Adaptors

TubeTop B

The TubeTop B has a 35 mm shaft and is used on the StandTek 3000, SpTek 4000 and the AlpTek 45 stands. It can also be used on the AlpTek 5500 and 6500, which have a 50 mm shaft with the aid of an Rlp5 adaptor. This adaptor is used for any application where you need to bolt a light, speaker and any other item to the top of a stand. It is made from steel and painted with Black Epoxy.

TubeTop C

The TubeTop C has a 35 mm shaft and is used on the StandTek 3000, SpTek 4000 and the AlpTek 45 stands. It can also be used on the AlpTek 5500 and 6500 which have a 50 mm shaft with the aid of an Rlp5 adaptor. This adaptor is used to secure a 2 inch pipe to the top of the stand to create a bridge between two stands or any other application where you need to connect a pipe. The base is black epoxy painted steel and the clamp is aluminum.

RLP5 Adaptor

The RLP5 adaptor is used to convert a 50 mm mast to a 35 mm mast. With this adaptor, you can use the 35 mm accessories on the AlpTek 5500 and 6500 stands. Zinc plated steel.

ASP Adaptor

The ASP adaptor is used to convert a 35 mm shaft to a 29 mm shaft. The 29 mm end is designed to receive a spigot shaft for adaptors made by other manufactures that have shafts. Black epoxy painted steel.

Accessories Brochure Information